Kingshowstar - LED Motorcycle Turn Signal Light Strip Flashing Tail Brake Stop Light LED Motorcycle Bicycle Light

Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.

Please read the following instructions thoroughly before installing this kit.

1. First using a tape measure, measure the lip under your bike to ensure there is enough clearance to mount your tail light bar, each of bike need two strip for right and left signals.

2. Following your bikes owner’s manual, carefully remove the parts from your bike if necessary.

3. Loose & route the wires to the place where planed to mounting the controller, using the supplied zip ties to secure the wire to their mounting points.

4. Double checked the mounting place is clean and dry, carefully peel back the edge of the adhesive baking on the connector end, place the LED strips on the clean and dry mounting place, use the supplied zip ties at each end of the strips to act as a secondary anchor and mounting point for each. The zip ties are a very important step and should not be skipped. They will help ensure that the lighting strips stay adhered and in place during vehicle use and trough seasonal temperature changes.

5. Route the Red & Black power wire from the Left signal switch, Connect and secure the power supply lines only after everything is properly installed and mounted.

6. Route the Red & Black power wire from the Left signal switch, Connect and secure the power supply lines only after everything is properly installed and mounted.

7. Then you turn on the bike and switch to left Flashing light, the original left signal light flashing, the strip scanning from right to left, when you switch to right Flashing light, the original right signal light flashing, the strip scanning from left to right.

8. The light have to connect to the flasher switch of the vehicle

Wire Connector Diagram:

Black Wire: Common Ground

Red Wire : DC 12V Positive

Brighter Than Expected High-quality LED chips emit bright and white light, reflector cups produce concentrated spot beam for long distance irradiation.	Extraordinary Waterproof Performance The Led light is well sealed by waterproof rubber pad and silicone sealing strip, fastening screws enhance the waterproof effect.	Outstanding Features With hard and durable aluminum alloy housing, quakeproof mounting bracket and cooling fins, the lifespan is over 30,000 hours.

>> Send Inquiry Now

>> View Home Page

>> View Home Page

View More  Send Inquiry Now

More lights and production trends, welcome to visit 

Shenzhen Kingshow Star Technology Co., Limited was established in shenzhen and our factory is located in Shenzhen, China. KingShow covers an area of 6,000 square meters and has about 400 employees, including 30 highly qualified staff members of specialists and engineers. We are a high-tech manufacturer specialized in led motorcycle light kit ,led auto/under light kit ,custom and normal LED strips, LED lamps, LED spotlights, LED bulbs, car lamps, wall washers, down lights, bedside lamps and other related LED products. Most of our products have CE and RoHS certificates. More than 90 percent of our products are delivered to Europe, North America and Australia.

>>Click to See More Product

King Show can satisfy your customized needs with our unparalleled advantages. We have been concentrating on the development, design and production of various electrical lighting appliances, such as automobile exquisite articles and colorful LED with professional technique, and we have been keeping good and direct business cooperation with the best LED chip suppliers in the USA and South Korea. Taking quality as priority, our QC staff members inspect all products piece by piece before delivery. Adequate tests must be conducted. We ensure that our products have good designs and top quality.

Our objective is to establish a long-term and steady relationship with you and we hope to become your reliable cooperative partner.Click to See Factory:https://

Don't hesitate, send "Inquiry" now !

View "Home Page" to get more information

Welcome to visit our factory!

We use PE Foam to separate the lights inside the cartons in order to protect all the lights products. For the large order, we use special bags to pack each light first, to avoid any scratch to the products. In some special cases, color box or display box are used to pack a set of 10pcs or 20pcs 30pcs etc.

Strong 5- layer thickness export cartons are used to pack the lights, which are hard and durable for goods that we export to our clients. In the meantime.shipping marks and side marks are printed on thecartons by computer printer as client's request.

Know More Details >>

>>Click Here To Get Our Latest Quote Now!

1.Please collect our product links and home page.

2.There are monthly updates collection for your choice!

3.There are occasional promotions and discounts for your better deal!

4.After collected our home web and product web,please show to our receptioniest,every order amount more than $1000 can get $10 discount,contact for order now.